|
Journal of Zhejiang University SCIENCE A
ISSN 1673-565X(Print), 1862-1775(Online), Monthly
2019 Vol.20 No.5 P.347-357
Design and numerical simulation of a clamshell-shaped inlet cover for air-breathing hypersonic vehicles
Abstract: An efficient clamshell-shaped inlet cover configuration based on a shockwave interference methodology is proposed, which has the advantage of an autonomous opening using the aerodynamic force and moment. A preliminary design method for the inlet cover is introduced and used to produce cover models of two different lengths, with contributions similar to those of cowlings, rocket fairings, shrouds, or false ogives. The clamshell-shaped inlet cover features a practical design with a wide range of applications, including utilization in air-breathing hypersonic vehicles under specific constraints. In this investigation, aerodynamic numerical simulations were conducted to evaluate the extent to which the objectives and design principles are achieved for two typical ballistic separation states. The results show that both configurations can prevent an excessive accumulation of shockwaves in the nose cone area. In addition, the inlet cover generates negative lift, which results in the generation of an opening moment. The calculated heat flux at the leading edge of the clamshell-shaped inlet cover is approximately 13 MW/m2, which is within the limit of the composite material but slightly higher than that of the stagnation point of the nose cone.
Key words: Aerodynamic configuration design; Novel inlet cover; Aerodynamic force; Heat evaluation
关键词组:
References:
[1]Blades EL, Newman III JC, 2013. Computational-fluid-dynamics-based design optimization of a large asymmetric payload fairing. Journal of Spacecraft and Rockets, 50(5):1013-1023.
[2]Brauckmann GJ, Streett C, Kleb WL, et al., 2015. Computational and experimental unsteady pressures for alternate SLS booster nose shapes. Proceedings of the 53rd AIAA Aerospace Sciences Meeting.
[3]Colonno MR, Alonso JJ, 2008. The optimum launch vehicle fairing: an MDO approach. Proceedings of the 12th AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference.
[4]Ding F, Shen CB, Liu J, et al., 2015. Influence of surface pressure distribution of basic flow field on shape and performance of waverider. Acta Astronautica, 108:62-78.
[5]Groves CE, Ilie M, Schallhorn PA, 2014. Computational fluid dynamics uncertainty analysis for payload fairing spacecraft environmental control systems. Proceedings of the 52nd Aerospace Sciences Meeting.
[6]Higgins JE, Biskner A, Sanford G, 2008. Design, fabrication, and testing of the minotaur IV large fairing. Proceedings of the 49th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, 16th AIAA/ASME/AHS Adaptive Structures Conference,10th AIAA Non-deterministic Approaches Conference, 9th AIAA Gossamer Spacecraft Forum, 4th AIAA Multidisciplinary Design Optimization Specialists Conference.
[7]Hong CQ, Han JC, Zhang XH, et al., 2013. Novel nanoporous silica aerogel impregnated highly porous ceramics with low thermal conductivity and enhanced mechanical properties. Scripta Materialia, 68(8):599-602.
[8]Kosareo DN, Oliver ST, Bednarcyk BA, et al., 2014. Buckling design and analysis of a payload fairing 1/6th cylindrical arc-segment panel. Proceedings of the 55th AIAA/ ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference.
[9]Li SB, Wang ZG, Huang W, et al., 2016. Effect of the injector configuration for opposing jet on the drag and heat reduction. Aerospace Science and Technology, 51:78-86.
[10]Liao L, Yan L, Huang W, et al., 2018. Mode transition process in a typical strut-based scramjet combustor based on a parametric study. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 19(6):431-451.
[11]Liu Z, Liu J, Ding F, et al., 2017. Effect of thermochemical non-equilibrium on the aerodynamics of an osculating-cone waverider under different angles of attack. Acta Astronautica, 139:288-295.
[12]Lockwood MK, Petley DH, Martin JG, et al., 1999. Airbreathing hypersonic vehicle design and analysis methods and interactions. Progress in Aerospace Sciences, 35(1):1-32.
[13]Lv Z, Xia ZX, Liu B, et al., 2017. Preliminary experimental study on solid-fuel rocket scramjet combustor. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 18(2):106-112.
[14]McClinton CR, Rausch VL, Shaw RJ, et al., 2005. Hyper-X: foundation for future hypersonic launch vehicles. Acta Astronautica, 57(2-8):614-622.
[15]Morshed MMM, Hansen CH, Zander AC, 2013. Prediction of acoustic loads on a launch vehicle fairing during liftoff. Journal of Spacecraft and Rockets, 50(1):159-168.
[16]Murman SM, Diosady LT, 2016. Simulation of a hammerhead payload fairing in the transonic regime. Proceedings of the 54th AIAA Aerospace Sciences Meeting.
[17]Sziroczak D, Smith H, 2016. A review of design issues specific to hypersonic flight vehicles. Progress in Aerospace Sciences, 84:1-28.
[18]Wang L, Zhu GX, Guan CQ, et al., 2016. Experimental investigation of dynamic separation for an inlet cover in Mach 6.0 flow. Proceedings of the 32nd AIAA Aerodynamic Measurement Technology and Ground Testing Conference.
[19]Yang XX, Zhou Z, Peng K, 2014. Aerodynamic shape design optimization of fairing based on kriging method. Journal of Solid Rocket Technology, 37(2):167-171 (in Chinese).
[20]Zhang XM, Yang SL, Li P, 2017. Numerical simulations of the inlet cover opening process. Journal of Solid Rocket Technology, 40(3):307-312 (in Chinese).
[21]Zhao R, Rong JL, Li YJ, et al., 2017. An investigation of fluctuating pressure environment around rocket fairing with different curvetypes. Acta Armamentarii, 38(5):1020-1026 (in Chinese).
Open peer comments: Debate/Discuss/Question/Opinion
<1>
DOI:
10.1631/jzus.A1800620
CLC number:
V43
Download Full Text:
Downloaded:
2429
Download summary:
<Click Here>Downloaded:
2027Clicked:
6263
Cited:
0
On-line Access:
2019-05-06
Received:
2018-11-02
Revision Accepted:
2019-03-27
Crosschecked:
2019-04-03