Similar articles

Abstract: The present work experimentally and numerically investigates the local heat transfer enhancement induced by a piezoelectric fan interacting with a cross flow in a local heated channel. The piezoelectric fan is placed along the flow direction and tested under different amplitudes and flow rates. In the simulations, a spring-based smoothing method and a local remeshing technique are used to handle the moving boundary problems. Hybrid mesh is used to reduce the size of dynamic mesh domain and to improve computational efficiency. The experimental and numerical values of the time-averaged mean Nusselt number are found to be in good agreement, with deviations of less than 10%. The experimental result shows that the heat transfer performance of the heated surfaces is substantially enhanced with a vibrating piezoelectric fan. The numerical result shows that the heat transfer enhancement comes from the strong longitudinal vortex pairs generated by the piezoelectric fan, which significantly promote heat exchange between the main flow and the near-wall flow. In the case of a=0.66 (a is the dimensionless amplitude) and Re=1820, the enhancement ratio of the time-averaged mean Nusselt number reaches 119.9%.

压电风扇对管内局部受迫对流换热的强化效果 研究

[1]Abdullah MK, Abdullah MZ, Ramana MV, et al., 2009. Numerical and experimental investigations on effect of fan height on the performance of piezoelectric fan in microelectronic cooling. International Communications in Heat and Mass Transfer, 36(1):51-58.

[2]Abdullah MK, Ismail NC, Abdullah MZ, et al., 2012a. Effects of tip gap and amplitude of piezoelectric fans on the performance of heat sinks in microelectronic cooling. Heat and Mass Transfer, 48(6):893-901.

[3]Abdullah MK, Ismail NC, Mujeebu MA, et al., 2012b. Optimum tip gap and orientation of multi-piezofan for heat transfer enhancement of finned heat sink in microelectronic cooling. International Journal of Heat and Mass Transfer, 55(21-22):5514-5525.

[4]Açikalin T, Wait SM, Garimella SV, et al., 2004. Experimental investigation of the thermal performance of piezoelectric fans. Heat Transfer Engineering, 25(1):4-14.

[5]Açikalin T, Garimella SV, Raman A, et al., 2007. Characterization and optimization of the thermal performance of miniature piezoelectric fans. International Journal of Heat and Fluid Flow, 28(4):806-820.

[6]Alsabery AI, Saleh H, Ghalambaz M, et al., 2019. Fluid-structure interaction analysis of transient convection heat transfer in a cavity containing inner solid cylinder and flexible right wall. International Journal of Numerical Methods for Heat & Fluid Flow, 29(10):3756-3780.

[7]Arshad A, Jabbal M, Yan YY, 2020. Synthetic jet actuators for heat transfer enhancement–a critical review. International Journal of Heat and Mass Transfer, 146:118815.

[8]Deng X, Luo ZB, Xia ZX, et al., 2019. Experimental investigation on the flow regime and impingement heat transfer of dual synthetic jet. International Journal of Thermal Sciences, 145:105864.

[9]Fairuz ZM, Sufian SF, Abdullah MZ, et al., 2014. Effect of piezoelectric fan mode shape on the heat transfer characteristics. International Communications in Heat and Mass Transfer, 52:140-151.

[10]Ghalambaz M, Jamesahar E, Ismael MA, et al., 2017. Fluid-structure interaction study of natural convection heat transfer over a flexible oscillating fin in a square cavity. International Journal of Thermal Sciences, 111:256-273.

[11]Ghalambaz M, Mehryan SAM, Izadpanahi E, et al., 2019a. MHD natural convection of Cu–Al₂O₃ water hybrid nanofluids in a cavity equally divided into two parts by a vertical flexible partition membrane. Journal of Thermal Analysis and Calorimetry, 138(2):1723-1743.

[12]Ghalambaz M, Chamkha AJ, Wen DS, 2019b. Natural convective flow and heat transfer of Nano-Encapsulated Phase Change Materials (NEPCMs) in a cavity. International Journal of Heat and Mass Transfer, 138:738-749.

[13]Ghalambaz M, Doostani A, Izadpanahi E, et al., 2020. Conjugate natural convection flow of Ag–MgO/water hybrid nanofluid in a square cavity. Journal of Thermal Analysis and Calorimetry, 139(3):2321-2336.

[14]Guo ZZ, He ZQ, Zhao WW, et al., 2018. Efficient mesh deformation and flowfield interpolation method for unstructured mesh. Acta Aeronautica et Astronautica Sinica, 39(12):126-137 (in Chinese).

[15]Hales A, Jiang X, 2018. A review of piezoelectric fans for low energy cooling of power electronics. Applied Energy, 215:321-337.

[16]Jamesahar E, Sabour M, Shahabadi M, et al., 2020. Mixed convection heat transfer by nanofluids in a cavity with two oscillating flexible fins: a fluid–structure interaction approach. Applied Mathematical Modelling, 82:72-90.

[17]Jeng TM, Liu CH, 2015. Moving-orientation and position effects of the piezoelectric fan on thermal characteristics of the heat sink partially filled in a channel with axial flow. International Journal of Heat and Mass Transfer, 85: 950-964.

[18]Jiang ZZ, Chen WF, Zhao WW, 2018. Numerical analysis of the micro-Couette flow using a non-Newton–Fourier model with enhanced wall boundary conditions. Microfluidics and Nanofluidics, 22(10), Article No. 10.

[19]Kimber M, Garimella SV, 2009. Cooling performance of arrays of vibrating cantilevers. Journal of Heat Transfer, 131(11):111401.

[20]Kurnia JC, Sasmito AP, Mujumdar AS, 2011. Evaluation of the heat transfer performance of helical coils of non-circular tubes. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 12(1):63-70.

[21]Lee YJ, Singh PK, Lee PS, 2015. Fluid flow and heat transfer investigations on enhanced microchannel heat sink using oblique fins with parametric study. International Journal of Heat and Mass Transfer, 81:325-336.

[22]Li XJ, Zhang JZ, Tan XM, 2017. Convective heat transfer on a flat surface induced by a vertically-oriented piezoelectric fan in the presence of cross flow. Heat and Mass Transfer, 53(9):2745-2768.

[23]Li XJ, Zhang JZ, Tan XM, 2018a. Effects of piezoelectric fan on overall performance of air-based micro pin-fin heat sink. International Journal of Thermal Sciences, 126: 1-12.

[24]Li XJ, Zhang JZ, Tan XM, 2018b. An investigation on convective heat transfer performance around piezoelectric fan vibration envelope in a forced channel flow. International Journal of Heat and Mass Transfer, 126:48-65.

[25]Lin CN, 2013. Enhanced heat transfer performance of cylindrical surface by piezoelectric fan under forced convection conditions. International Journal of Heat and Mass Transfer, 60:296-308.

[26]Liu SF, Huang RT, Sheu WJ, et al., 2009. Heat transfer by a piezoelectric fan on a flat surface subject to the influence of horizontal/vertical arrangement. International Journal of Heat and Mass Transfer, 52(11-12):2565-2570.

[27]Ma HK, Su HC, Liu CL, et al., 2012. Investigation of a piezoelectric fan embedded in a heat sink. International Communications in Heat and Mass Transfer, 39(5):603-609.

[28]Mehryan SAM, Izadpanahi E, Ghalambaz M, et al., 2019. Mixed convection flow caused by an oscillating cylinder in a square cavity filled with Cu-Al₂O₃/water hybrid nanofluid. Journal of Thermal Analysis and Calorimetry, 137(3):965-982.

[29]Moffat RJ, 1988. Describing the uncertainties in experimental results. Experimental Thermal and Fluid Science, 1(1):3-17.

[30]Peles Y, Koşar A, Mishra C, et al., 2005. Forced convective heat transfer across a pin fin micro heat sink. International Journal of Heat and Mass Transfer, 48(17):3615-3627.

[31]Sufian SF, Abdullah MZ, Mohamed JJ, 2013. Effect of synchronized piezoelectric fans on microelectronic cooling performance. International Communications in Heat and Mass Transfer, 43:81-89.

[32]Wait SM, Basak S, Garimella SV, et al., 2007. Piezoelectric fans using higher flexural modes for electronics cooling applications. IEEE Transactions on Components and Packaging Technologies, 30(1):119-128.

[33]Wang XQ, Mujumdar AS, 2007. Heat transfer characteristics of nanofluids: a review. International Journal of Thermal Sciences, 46(1):1-19.

[34]Wen DS, Lin GP, Vafaei S, et al., 2009. Review of nanofluids for heat transfer applications. Particuology, 7(2):141-150.

[35]Xia CC, Chen WF, 2016. Boundary-layer transition prediction using a simplified correlation-based model. Chinese Journal of Aeronautics, 29(1):66-75.

[36]Xu Y, Moon C, Wang JJ, et al., 2019. An experimental study on the flow and heat transfer of an impinging synthetic jet. International Journal of Heat and Mass Transfer, 144: 118626.

[37]Yeom T, Simon TW, North M, et al., 2016. High-frequency translational agitation with micro pin-fin surfaces for enhancing heat transfer of forced convection. International Journal of Heat and Mass Transfer, 94:354-365.