Full Text:
<2618>
CLC number: R733.7
On-line Access:
Received: 2006-03-29
Revision Accepted: 2006-06-03
Crosschecked: 0000-00-00
Cited: 0
Clicked: 4548
Technological requirements of profile machining
| |||||||||||||
PARK Sangchul, CHUNG Yunchan. Technological requirements of profile machining[J]. Journal of Zhejiang University Science A, 2006, 7(9): 1461-1466.
@article{title="Technological requirements of profile machining",
author="PARK Sangchul, CHUNG Yunchan",
journal="Journal of Zhejiang University Science A",
volume="7",
number="9",
pages="1461-1466",
year="2006",
publisher="Zhejiang University Press & Springer",
doi="10.1631/jzus.2006.A1461"
}
%0 Journal Article
%T Technological requirements of profile machining
%A PARK Sangchul
%A CHUNG Yunchan
%J Journal of Zhejiang University SCIENCE A
%V 7
%N 9
%P 1461-1466
%@ 1673-565X
%D 2006
%I Zhejiang University Press & Springer
%DOI 10.1631/jzus.2006.A1461
TY - JOUR
T1 - Technological requirements of profile machining
A1 - PARK Sangchul
A1 - CHUNG Yunchan
J0 - Journal of Zhejiang University Science A
VL - 7
IS - 9
SP - 1461
EP - 1466
%@ 1673-565X
Y1 - 2006
PB - Zhejiang University Press & Springer
ER -
DOI - 10.1631/jzus.2006.A1461
Abstract: The term ‘profile machining’ is used to refer to the milling of vertical surfaces described by profile curves. profile machining requires higher precision (1/1000 mm) than regular 3D machining (1/100 mm) with the erosion of sharp vertices should being especially avoided. Although, profile machining is very essential for making trimming and flange dies, it seldom brought into focus. This paper addresses the technological requirements of profile machining including machining width and depth control, minimizing toolware, and protecting sharp vertices. Issues of controller alarms are also addressed.
[1] Bae, S.H., Ko, K., Kim, B.H., Choi, B.K., 2003. Automatic feedrate adjustment for pocket machining. Computer-Aided Design, 35(5):495-500.
[2] Choi, B.K., Park, S.C., 1999. A pair-wise offset algorithm for 2D point-sequence. Computer-Aided Design, 31(12):735-745.
[3] Fanuc Ltd., 1993. Fanuc Series 15-Model B, Maintenance Manual, 1(2):100.
[4] Geoffrey, B., 1975. Fundamentals of Metal Machining and Machine Tools. McGraw-Hill, p.29-39.
[5] Park, S.C., Chung, Y.C., 2003. Mitered offset for profile machining. Computer-Aided Design, 35(5):501-505.
[6] Schonherr, J., 1993. Smooth biarc curves. Computer-Aided Design, 25(6):365-370.
[7] Shin, H., Jeong, H.M., Kwak, Y.S., 1995. Machining of 2D parametric spline using cutter radius compensation. IE Interface, 8(3):133-139.
[8] Shin, H., Yoo, S.K., Cho, S.K., Chung, W.H., 2003. Directional offset of a spatial curve for practical engineering design. Lecture Notes in Computer Science, 2669:711-720.
[9] Yeung, M.K., Walton, D.J., 1994. Curve fitting with arc spline for NC tool path generation. Computer-Aided Design, 26(11):845-849.
Open peer comments: Debate/Discuss/Question/Opinion
<1>