Similar articles

Abstract: limestone calcined clay cement (LC3) is an environment-friendly and sustainable cementitious material. It has recently gained considerable attention for the stabilization/solidification (S/S) of soils contaminated by heavy metals. However, the existing studies on S/S of zn-contaminated soils using LC3 in terms of hydraulic conductivity and microstructural properties as compared to ordinary Portland cement (OPC) are limited. This study focuses on the evaluation of the mechanical, leaching, and microstructural characteristics of zn-contaminated soils treated with different contents (0%, 4%, 6%, 8%, and 10%) of low-carbon LC3. The engineering performance of the treated zn-contaminated soils is assessed over time using unconfined compressive strength (UCS), hydraulic conductivity (k), toxicity characteristic leaching procedure (TCLP), and synthetic precipitation leaching procedure (SPLP) tests. Experimental results show that the UCS of zn-contaminated soils treated with LC3 ranged from 1.47 to 2.49 MPa, which is higher than 1.63%‍–‍13.07% for those treated with OPC. The k of zn-contaminated soils treated with LC3 ranged from 1.16×10^-8 to 5.18×10^-8 cm/s as compared to the OPC treated samples. For the leaching properties, the leached Zn from TCLP and SPLP is 1.58‍–‍321.10 mg/L and 0.52‍–‍284.65 mg/L as the LC3 contents ranged from 4% to 10%. Further, the corresponding pH modeling results indicate that LC3 promotes a relatively suitable dynamic equilibrium condition to immobilize the higher-level Zn contamination. In addition, microscopic analyses demonstrate that the formations of hydration products, i.‍e., Zn(OH)₂, Zn₂SiO₄, calcium silicate hydrate (C–S–H), calcium silicate aluminate hydrate (C‍–‍A‍–‍S‍–‍H) gel, ettringite, and CaZn(SiO₄)(H₂O), are the primary mechanisms for the immobilization of Zn. This study also provides an empirical formula between the UCS and k to support the application of LC3-solidified zn-contaminated soils in practical engineering in the field.

可持续石灰石煅烧粘土水泥(LC3)固化剂处理锌污染土的环境岩土特性及微观结构特征

[1]AlbinoV, CioffiR, MarroccoliM, et al., 1996. Potential application of ettringite generating systems for hazardous waste stabilization. Journal of Hazardous Materials, 51(1-3):241-252.

[2]AvetF, SnellingsR, DiazAA, et al., 2016. Development of a new rapid, relevant and reliable (R³) test method to evaluate the pozzolanic reactivity of calcined kaolinitic clays. Cement and Concrete Research, 85:1-11.

[3]BakeraAT, AlexanderMG, 2019. Use of metakaolin as supplementary cementitious material in concrete, with focus on durability properties. RILEM Technical Letters, 4:89-102.

[4]BeaudoinJ, OdlerI, 2019. Hydration, setting and hardening of Portland cement. In: Hewlett PC, Liska M (Eds.), Lea’s Chemistry of Cement and Concrete, 5th Edition. Butterworth-Heinemann, Cambridge, UK, p.157-250.

[5]BucherR, DiederichP, EscadeillasG, et al., 2017. Service life of metakaolin-based concrete exposed to carbonation: comparison with blended cement containing fly ash, blast furnace slag and limestone filler. Cement and Concrete Research, 99:18-29.

[6]BujI, TorrasJ, RoviraM, et al., 2010. Leaching behaviour of magnesium phosphate cements containing high quantities of heavy metals. Journal of Hazardous Materials, 175(1-3):789-794.

[7]CapassoI, LirerS, FloraA, et al., 2019. Reuse of mining waste as aggregates in fly ash-based geopolymers. Journal of Cleaner Production, 220:65-73.

[8]ChenJ, ChenJZ, TanMZ, et al., 2002. Soil degradation: a global problem endangering sustainable development. Journal of Geographical Sciences, 12(2):243-252.

[9]ChenL, WangL, ChoDW, et al., 2019. Sustainable stabilization/solidification of municipal solid waste incinerator fly ash by incorporation of green materials. Journal of Cleaner Production, 222:335-343.

[10]ChoiYC, ParkB, 2020. Effects of high-temperature exposure on fractal dimension of fly-ash-based geopolymer composites. Journal of Materials Research and Technology, 9(4):7655-7668.

[11]CuisinierO, Le BorgneT, DeneeleD, et al., 2011. Quantification of the effects of nitrates, phosphates and chlorides on soil stabilization with lime and cement. Engineering Geology, 117(3-4):229-235.

[12]de Andrade LimaLRP, BernardezLA, 2013. Evaluation of the chemical stability of a landfilled primary lead smelting slag. Environmental Earth Sciences, 68(4):1033-1040.

[13]DengL, ShiZ, 2015. Synthesis and characterization of a novel Mg‍–‍Al hydrotalcite-loaded kaolin clay and its adsorption properties for phosphate in aqueous solution. Journal of Alloys and Compounds, 637:188-196.

[14]DixitA, DuHJ, PangSD, 2021. Performance of mortar incorporating calcined marine clays with varying kaolinite content. Journal of Cleaner Production, 282:124513.

[15]DrissiS, ShiCJ, LiN, et al., 2021. Relationship between the composition and hydration-microstructure-mechanical pro

[16]perties of cement-metakaolin-limestone ternary system. Construction and Building Materials, 302:124175.

[17]DuYJ, JiangNJ, LiuSY, et al., 2014. Engineering properties and microstructural characteristics of cement-stabilized zinc-contaminated kaolin. Canadian Geotechnical Journal, 51(3):289-302.

[18]ElbltagyHM, ElbasiounyH, AlmuhamadyA, et al., 2021. Low cost and eco-friendly removal of toxic heavy metal from industrial wastewater. Egyptian Journal of Soil Science, 61(2):219-229.

[19]Garcia-LodeiroI, PalomoA, Fernández-JiménezA, et al., 2011. Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O‍–‍CaO‍–‍Al2O3‍–SiO2‍–‍H2O. Cement and Concrete Research, 41(9):‍923-931.

[20]GengGQ, MyersRJ, LiJQ, et al., 2017. Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate. Scientific Reports, 7:44032.

[21]GuYC, LiJL, PengJK, et al., 2020. Immobilization of hazardous ferronickel slag treated using ternary limestone calcined clay cement. Construction and Building Materials, 250:118837.

[22]HalimCE, AmalR, BeydounD, et al., 2003. Evaluating the applicability of a modified toxicity characteristic leaching procedure (TCLP) for the classification of cementitious wastes containing lead and cadmium. Journal of Hazardous Materials, 103(1-2):125-140.

[23]HanRR, ZhouBH, HuangYY, et al., 2020. Bibliometric overview of research trends on heavy metal health risks and impacts in 1989–2018. Journal of Cleaner Production, 276:123249.

[24]HosanA, ShaikhFUA, 2021. Compressive strength development and durability properties of high volume slag and slag-fly ash blended concretes containing nano-CaCO₃. Journal of Materials Research and Technology, 10:‍1310-1322.

[25]HuangX, HuangT, LiS, et al., 2016. Immobilization of chromite ore processing residue with alkali-activated blast furnace slag-based geopolymer. Ceramics International, 42(8):9538-9549.

[26]KapelusznaE, KotwicaŁ, RóżyckaA, et al., 2017. Incorporation of Al in C-A-S-H gels with various Ca/Si and Al/Si ratio: microstructural and structural characteristics with DTA/TG, XRD, FTIR and TEM analysis. Construction and Building Materials, 155:643-653.

[27]KhalidS, ShahidM, NiaziNK, et al., 2017. A comparison of technologies for remediation of heavy metal contaminated soils. Journal of Geochemical Exploration, 182:247-268.

[28]KogbaraRB, Al-TabbaaA, YiYL, et al., 2012. pH-dependent leaching behaviour and other performance properties of cement-treated mixed contaminated soil. Journal of Environmental Sciences, 24(9):1630-1638.

[29]KuaTA, ArulrajahA, HorpibulsukS, et al., 2016. Strength assessment of spent coffee grounds-geopolymer cement utilizing slag and fly ash precursors. Construction and Building Materials, 115:565-575.

[30]LiuXM, ZhaoXB, YinHF, et al., 2018. Intermediate-calcium based cementitious materials prepared by MSWI fly ash and other solid wastes: hydration characteristics and heavy metals solidification behavior. Journal of Hazardous Materials, 349:262-271.

[31]MEP (Ministry of Environmental Protection of the People’s Republic of China), 2014. China Soil Pollution Survey Communique. MEP, Beijing, China(in Chinese).

[32]MoghalAAB, AshfaqM, Al-ShamraniMA, et al., 2020. Effect of heavy metal contamination on the compressibility and strength characteristics of chemically modified semiarid soils. Journal of Hazardous, Toxic, and Radioactive Waste, 24(4):04020029.

[33]MWR (Ministry of Water Resources of the People’s Republic of China), 2019. Standard for Geotechnical Testing Method, GB/T 50123‍–‍2019. National Standards of the People’s Republic of China(in Chinese).

[34]PandeyB, KinradeSD, CatalanLJJ, 2012. Effects of carbonation on the leachability and compressive strength of cement-solidified and geopolymer-solidified synthetic metal wastes. Journal of Environmental Management, 101:‍59-67.

[35]PantazopoulouE, NtinoudiE, ZouboulisAI, et al., 2020. Heavy metal stabilization of industrial solid wastes using low-grade magnesia, Portland and magnesia cements. Journal of Material Cycles and Waste Management, 22(4):‍975-985.

[36]PariaS, YuetPK, 2006. Solidification–stabilization of organic and inorganic contaminants using Portland cement: a literature review. Environmental Reviews, 14(4):217-255.

[37]ParusA, FramskiG, 2018. Impact of O-alkyl-pyridineamidoximes on the soil environment. Science of the Total Environment, 643:1278-1284.

[38]ParusA, IdziakM, JacewiczP, et al., 2021. Assessment of environmental risk caused by the presence of antibiotics. Environmental Nanotechnology, Monitoring & Management, 16:100533.

[39]PengDD, WangYG, LiuXM, et al., 2019. Preparation, characterization, and application of an eco-friendly sand-fixing material largely utilizing coal-based solid waste. Journal of Hazardous Materials, 373:294-302.

[40]QianGR, SunDD, TayJH, 2003. Immobilization of mercury and zinc in an alkali-activated slag matrix. Journal of Hazardous Materials, 101(1):65-77.

[41]ReddyVA, SolankiCH, KumarS, et al., 2019. New ternary blend limestone calcined clay cement for solidification/stabilization of zinc contaminated soil. Chemosphere, 235:308-315.

[42]ReddyVA, SolankiCH, KumarS, et al., 2020. Stabilization/solidification of zinc- and lead-contaminated soil using limestone calcined clay cement (LC³): an environmentally friendly alternative. Sustainability, 12(9):3725.

[43]ReddyVA, SolankiCH, KumarS, et al., 2022. Comparison of limestone calcined clay cement and ordinary Portland cement for stabilization/solidification of Pb-Zn smelter residue. Environmental Science and Pollution Research, 29(8):11393-11404.

[44]ScrivenerKL, 2014. Options for the future of cement. The Indian Concrete Journal, 88(7):11-21.

[45]SennecaO, CorteseL, di MartinoR, et al., 2020. Mechanisms affecting the delayed efficiency of cement based stabilization/solidification processes. Journal of Cleaner Production, 261:121230.

[46]SnehalK, DasB, 2022. Pozzolanic reactivity and drying shrinkage characteristics of optimized blended cementitious composites comprising of Nano-Silica particles. Construction and Building Materials, 316:125796.

[47]SEPA (State Environmental Protection Administration), 2007. Identification Standards for Hazardous Wastes‍–Identification for Extraction Toxicity, GB 5085.3‍–‍2007. National Standards of the People’s Republic of China(in Chinese).

[48]TangJ, WeiSF, LiWF, et al., 2019. Synergistic effect of metakaolin and limestone on the hydration properties of Portland cement. Construction and Building Materials, 223:177-184.

[49]USEPA (United States Environmental Protection Agency), 1992. SW-846 Test Method 1311: Toxicity Characteristic Leaching Procedure. USEPA, USA.

[50]USEPA (United States Environmental Protection Agency), 1994. SW-846 Test Method 1312: Synthetic Precipitation Leaching Procedure. USEPA, USA.

[51]WangH, HouPK, LiQF, et al., 2021. Synergistic effects of supplementary cementitious materials in limestone and calcined clay-replaced slag cement. Construction and Building Materials, 282:122648.

[52]WangL, ChenL, TsangDCW, et al., 2018. Green remediation of contaminated sediment by stabilization/solidification with industrial by-products and CO₂ utilization. Science of the Total Environment, 631-632:1321-1327.

[53]WangL, ChoDW, TsangDCW, et al., 2019. Green remediation of As and Pb contaminated soil using cement-free clay-based stabilization/solidification. Environment International, 126:336-345.

[54]WangL, GeddesDA, WalkleyB, et al., 2020. The role of zinc in metakaolin-based geopolymers. Cement and Concrete Research, 136:106194.

[55]WuHL, JinF, BoYL, et al., 2018. Leaching and microstructural properties of lead contaminated kaolin stabilized by GGBS-MgO in semi-dynamic leaching tests. Construction and Building Materials, 172:626-634.

[56]XueST, 2018. Study on the Effect and Mechanism of Zinc Compounds on the Properties of Cement-Based Materials. MS Thesis, Zhejiang University of Technology, Hangzhou, China(in Chinese).

[57]YadavAL, SairamV, MuruganandamL, et al., 2020. An overview of the influences of mechanical and chemical processing on sugarcane bagasse ash characterisation as a supplementary cementitious material. Journal of Cleaner Production, 245:118854.

[58]YuJ, WuHL, MishraDK, et al., 2021. Compressive strength and environmental impact of sustainable blended cement with high-dosage limestone and calcined clay (LC2). Journal of Cleaner Production, 278:123616.

[59]ZhangYL, LiuXM, XuYT, et al., 2020. Preparation of road base material by utilizing electrolytic manganese residue based on Si-Al structure: mechanical properties and Mn²⁺ stabilization/solidification characterization. Journal of Hazardous Materials, 390:122188.

[60]ZhangYY, WangL, ChenL, et al., 2021. Treatment of municipal solid waste incineration fly ash: state-of-the-art technologies and future perspectives. Journal of Hazardous Materials, 411:125132.