Similar articles

Abstract: A distributed fault-tolerant strategy for the controller area network based electric swing system of hybrid excavators is proposed to achieve good performance under communication errors based on the adaptive compensation of the delays and packet dropouts. The adverse impacts of communication errors are effectively reduced by a novel delay compensation scheme, where the feedback signal and the control command are compensated in each control period in the central controller and the swing motor driver, respectively, without requiring additional network bandwidth. The recursive least-squares algorithm with forgetting factor algorithm is employed to identify the time-varying model parameters due to pose variation, and a reverse correction law is embedded into the feedback compensation in consecutive packet dropout scenarios to overcome the impacts of the model error. Simulations and practical experiments are conducted. The results show that the proposed fault-tolerant strategy can effectively reduce the communication-error-induced overshoot and response time variation.

混合动力挖掘机电动回转系统通信错误状态下的分布式容错策略

[1]Beza, M., Bongiorno, M., 2014. Application of recursive least squares algorithm with variable forgetting factor for frequency component estimation in a generic input signal. IEEE Trans. Ind. Appl., 50(2):1168-1176.

[2]Du, Z., Yue, D., Hu, S., 2014. H-infinity stabilization for singular networked cascade control systems with state delay and disturbance. IEEE Trans. Ind. Inform., 10(2):882-894.

[3]Gao, D., Wang, Q., 2014. Health monitoring of controller area network in hybrid excavator based on the message response time. IEEE/ASME Int. Conf. on Advanced Intelligent Mechatronics, p.1634-1639.

[4]Gao, D., Wang, Q., Lei, Y., et al., 2015. Online real-time estimation of response time for periodic messages in controller area networks. Math. Prob. Eng., 2015:1-13.

[5]Gupta, R.A., Chow, M.Y., 2010. Networked control system: overview and research trends. IEEE Trans. Ind. Electron., 57(7):2527-2535.

[6]ISO, 2015. Road Vehicles—Controller Area Network (CAN)—Part 1: Data Link Layer and Physical Signalling, ISO 11898-1:2015. International Organization for Stan-dardization, Geneva.

[7]Jin, K., Park, T., Lee, H., 2012. A control method to suppress the swing vibration of a hybrid excavator using sliding mode approach. Proc. Inst. Mech. Eng. C, 226(5): 1237-1253.

[8]Kagoshima, M., Komiyama, M., Nanjo, T., et al., 2007. Development of new hybrid excavator. Kobelco Technol. Rev., 27:39-42.

[9]Katrasnik, T., 2007. Hybridization of powertrain and downsizing of IC ICE—a way to reduce fuel consumption and pollutant emissions—Part 1. Energy Conv. Manag., 48(5):1411-1423.

[10]Kim, H., Choi, J., Yi, K., 2012. Development of supervisory control strategy for optimized fuel consumption of the compound hybrid excavator. Proc. Inst. Mech. Eng. D, 226(12):1652-1666.

[11]Kim, J.Y., 2014. Anti-Rebounding Control Apparatus and Method in an Electrical Swing System of a Hybrid Excavator. E.P. Patent 2 690 224 A1.

[12]Kruszewski, A., Jiang, W.J., Fridman, E., et al., 2012. A switched system approach to exponential stabilization through communication network. IEEE Trans. Contr. Syst. Technol., 20(4):887-900.

[13]Kwon, T., Lee, S., Sul, S., et al., 2010. Power control algorithm for hybrid excavator with super capacitor. IEEE Trans. Ind. Appl., 46(4):1447-1455.

[14]Lei, Y., Yuan, Y., Zhao, J., 2014. Model-based detection and monitoring of the intermittent connections for CAN networks. IEEE Trans. Ind. Electron., 61(6):2912-2921.

[15]Lin, T., Wang, Q., Hu, B., et al., 2010a. Development of hybrid powered hydraulic construction machinery. Autom. Constr., 19(1):11-19.

[16]Lin, T., Wang, Q., Hu, B., et al., 2010b. Research on the energy regeneration systems for hybrid hydraulic excavators. Autom. Constr., 19(8):1016-1026.

[17]Liu, G.P., Xia, Y., Chen, J., et al., 2007. Networked predictive control of systems with random network delays in both forward and feedback channels. IEEE Trans. Ind. Electron., 54(3):1282-1297.

[18]Luck, R., Ray, A., 1990. An observer-based compensator for distributed delays. Automatica, 26(5):903-908.

[19]Luck, R., Ray, A., 1994. Experimental verification of a delay compensation algorithm for integrated communication and control systems. Int. J. Contr., 59(6):1357-1372.

[20]Nilsson, J., 1998. Real-Time Control Systems with Delays. PhD Thesis, Department of Automatic Control, Lund Institute of Technology, Lund, Sweden.

[21]Rahmani, B., Markazi, A.H.D., 2013. Variable selective control method for networked control systems. IEEE Trans. Contr. Syst. Technol., 21(3):975-982.

[22]Shi, Y., Yu, B., 2011. Robust mixed H₂/H_∞ control of networked control systems with random time delays in both forward and backward communication links. Automatica, 47(4):754-760.

[23]Shi, Y., Huang, J., Yu, B., 2013. Robust tracking control of networked control systems application to a networked DC motor. IEEE Trans. Ind. Electron., 60(12):5864-5874.

[24]Shuai, Z., Zhang, H., Wang, J., et al., 2014. Combined AFS and DYC control of four-wheel-independent-drive electric vehicles over CAN network with time-varying delays. IEEE Trans. Veh. Technol., 63(2):591-602.

[25]Song, H., Liu, G.P., Yu, L., 2013. Networked predictive control of uncertain systems with multiple feedback channels. IEEE Trans. Ind. Electron., 60(11):5228-5238.

[26]Tian, Y.C., Levy, D., 2008. Compensation for control packet dropout in networked control systems. Inf. Sci., 178(5):1263-1278.

[27]Tipsuwan, Y., Chow, M.Y., 2004. Gain scheduler middleware: a methodology to enable existing controllers for networked control and teleoperation—part I: networked control. IEEE Trans. Ind. Electron., 51(6):1218-1227.

[28]Wang, D., Guan, C., Pan, S., et al., 2009. Performance analysis of hydraulic excavator powertrain hybridization. Autom. Constr., 18(3):249-257.

[29]Wang, Q., Zhang, Y., Xiao, Q., 2005. Evaluation for energy saving effect and simulation research on energy saving of hydraulic system in hybrid construction machinery. Chin. J. Mech. Eng., 41(12):35-140.

[30]Wang, T., Wang, Q., 2014. An energy-saving pressure-compensated hydraulic system with electrical approach. IEEE/ASME Trans. Mechatron., 19(2):570-578.

[31]Wang, Y., Sun, X., Wang, Z., et al., 2014. Construction of Lyapunov–Krasovskii functionals for switched nonlinear systems with input delay. Automatica, 50(4):1249-1253.

[32]Xiao, Q., Wang, Q., Zhang, Y., 2008. Control strategies of power system in hybrid hydraulic excavator. Autom. Constr., 17(4):361-367.

[33]Yang, R., Liu, G.P., Shi, P., et al., 2014. Predictive output feedback control for networked control systems. IEEE Trans. Ind. Electron., 61(1):512-520.

[34]Yao, H., Wang, Q., 2015. The control strategy of improving the stability of powertrain for compound hybrid power excavator. Proc. Inst. Mech. Eng. D J. Autom. Eng., 229(5):1-15.

[35]Zhang, L., Gao, H., Kaynak, O., 2013. Network-induced constraints in networked control systems—a survey. IEEE Trans. Ind. Inf., 9(1):403-416.