Similar articles

Abstract: As a promising enhanced gas recovery technique, CO₂ huff-n-puff has attracted great attention recently. However, hydraulic fracture deformation hysteresis is rarely considered, and its effect on CO₂ huff-n-puff performance is not well understood. In this study, we present a fully coupled multi-component flow and geomechanics model for simulating CO₂ huff-n-puff in shale gas reservoirs considering hydraulic fracture deformation hysteresis. Specifically, a shale gas reservoir after hydraulic fracturing is modeled using an efficient hybrid model incorporating an embedded discrete fracture model (EDFM), multiple porosity model, and single porosity model. In flow equations, Fick’s law, extended Langmuir isotherms, and the Peng-Robinson equation of state are used to describe the molecular diffusion, multi-component adsorption, and gas properties, respectively. In relation to geomechanics, a path-dependent constitutive law is applied for the hydraulic fracture deformation hysteresis. The finite volume method (FVM) and the stabilized extended finite element method (XFEM) are applied to discretize the flow and geomechanics equations, respectively. We then solve the coupled model using the fixed-stress split iterative method. Finally, we verify the presented method using several numerical examples, and apply it to investigate the effect of hydraulic fracture deformation hysteresis on CO₂ huff-n-puff performance in a 3D shale gas reservoir. Numerical results show that hydraulic fracture deformation hysteresis has some negative effects on CO₂ huff-n-puff performance. The effects are sensitive to the initial conductivity of hydraulic fracture, production pressure, starting time of huff-n-puff, injection pressure, and huff-n-puff cycle number.

水力裂缝变形滞后对页岩气藏CO₂吞吐的影响研究

[1](Computer Modelling Group)CMG, 2015. GEM User’s Guide. Computer Modelling Group, Calgary, Canada.

[2]COMSOL, 1998. Introduction to COMSOL Multiphysics®. COMSOL, Burlington, USA.

[3]DuFS, NojabaeiB, 2019. A review of gas injection in shale reservoirs: enhanced oil/gas recovery approaches and greenhouse gas control. Energies, 12(12):2355.

[4]FanWP, SunH, YaoJ, et al., 2019. An upscaled transport model for shale gas considering multiple mechanisms and heterogeneity based on homogenization theory. Journal of Petroleum Science and Engineering, 183:106392.

[5]FathiE, AkkutluIY, 2014. Multi-component gas transport and adsorption effects during CO₂ injection and enhanced shale gas recovery. International Journal of Coal Geology, 123:52-61.

[6]GalaD, SharmaM, 2018. Compositional and geomechanical effects in huff-n-puff gas injection IOR in tight oil reservoirs. SPE Annual Technical Conference and Exhibition, p.1-24.

[7]GaripovTT, Karimi-FardM, TchelepiHA, 2016. Discrete fracture model for coupled flow and geomechanics. Computational Geosciences, 20(1):149-160.

[8]GhanizadehA, ClarksonCR, DeglintH, et al., 2016. Unpropped/propped fracture permeability and proppant embedment evaluation: a rigorous core-analysis/imaging methodology. Proceedings of the SPE/AAPG/SEG Unconventional Resources Technology Conference, p.1824-1852.

[9]GigerF, ReissL, JourdanA, 1984. The reservoir engineering aspects of horizontal drilling. SPE Annual Technical Conference and Exhibition, p.1-8.

[10]GodecM, KopernaG, PetrusakR, et al., 2014. Enhanced gas recovery and CO₂ storage in gas shales: a summary review of its status and potential. Energy Procedia, 63:5849-5857.

[11]HasanM, EliebidM, MahmoudM, et al., 2017. Enhanced gas recovery (EGR) methods and production enhancement techniques for shale & tight gas reservoirs. SPE Kingdom of Saudi Arabia Annual Technical Symposium and Exhibition, p.1-9.

[12]HuangJW, JinTY, BarrufetM, et al., 2020. Evaluation of CO₂ injection into shale gas reservoirs considering dispersed distribution of kerogen. Applied Energy, 260:114285.

[13]HubbertM, WillisDG, 1957. Mechanics of hydraulic fracturing. Transactions of the AIME, 210(1):153-168.

[14]IEA (International Energy Agency), 2021. Levelised Cost of CO₂ Capture by Sector and Initial CO₂ Concentration, 2019. IEA, Paris, France. https://www.iea.org/data-and-statistics/charts/levelised-cost-of-co2-capture-by-sector-and-initial-co2-concentration-2019

[15]IEA (International Energy Agency), 2022. Natural Gas Prices in Europe, Asia and the United States, Jan 2020-February 2022. IEA, Paris, France. https://www.iea.org/data-and-statistics/charts/natural-gas-prices-in-europe-asia-and-the-united-states-jan-2020-february-2022

[16]JaegerJC, CookNGW, ZimmermanRW, 2007. Fundamentals of Rock Mechanics, 4th Edition. Blackwell Publishing, Oxford, UK, p.189-194.

[17]JiangJM, YangJ, 2018. Coupled fluid flow and geomechanics modeling of stress-sensitive production behavior in fractured shale gas reservoirs. International Journal of Rock Mechanics and Mining Sciences, 101:1-12.

[18]JiangJM, ShaoYY, YounisRM, 2014. Development of a multi-continuum multi-component model for enhanced gas recovery and CO₂ storage in fractured shale gas reservoirs. SPE Improved Oil Recovery Symposium, p.1-17.

[19]KarlssonH, JacquesGE, HattenJL, et al., 1991. Method and Apparatus for Horizontal Drilling. US Patent 5074366.

[20]KhoeiAR, 2014. Extended Finite Element Method: Theory and Applications. John Wiley & Sons, Chichester, UK.

[21]KimJ, MoridisGJ, 2014. Gas flow tightly coupled to elastoplastic geomechanics for tight-and shale-gas reservoirs: material failure and enhanced permeability. SPE Journal, 19(6):1110-1125.

[22]KimJ, SonnenthalEL, RutqvistJ, 2012. Formulation and sequential numerical algorithms of coupled fluid/heat flow and geomechanics for multiple porosity materials. International Journal for Numerical Methods in Engineering, 92(5):425-456.

[23]KimTH, ChoJ, LeeKS, 2017. Evaluation of CO₂ injection in shale gas reservoirs with multi-component transport and geomechanical effects. Applied Energy, 190:1195-1206.

[24]LiHL, LuYY, ZhouL, et al., 2017. A new constitutive model for calculating the loading-path dependent proppant deformation and damage analysis of fracture conductivity. Journal of Natural Gas Science and Engineering, 46:365-374.

[25]LiZY, ElsworthD, 2019. Controls of CO₂–N₂ gas flood ratios on enhanced shale gas recovery and ultimate CO₂ sequestration. Journal of Petroleum Science and Engineering, 179:1037-1045.

[26]LiuFS, BorjaRI, 2010. Stabilized low-order finite elements for frictional contact with the extended finite element method. Computer Methods in Applied Mechanics and Engineering, 199(37-40):2456-2471.

[27]LiuJ, WangJG, GaoF, et al., 2019. A fully coupled fracture equivalent continuum-dual porosity model for hydro-mechanical process in fractured shale gas reservoirs. Computers and Geotechnics, 106:143-160.

[28]LiuJS, ChenZW, ElsworthD, et al., 2011. Interactions of multiple processes during CBM extraction: a critical review. International Journal of Coal Geology, 87(3-4):175-189.

[29]LiuLJ, YaoJ, SunH, et al., 2019. Compositional modeling of shale condensate gas flow with multiple transport mechanisms. Journal of Petroleum Science and Engineering, 172:1186-1201.

[30]LiuLJ, LiuYZ, YaoJ, et al., 2020a. Efficient coupled multiphase-flow and geomechanics modeling of well performance and stress evolution in shale-gas reservoirs considering dynamic fracture properties. SPE Journal, 25(3):‍1523-1542.

[31]LiuLJ, LiuYZ, YaoJ, et al., 2020b. Mechanistic study of cyclic water injection to enhance oil recovery in tight reservoirs with fracture deformation hysteresis. Fuel, 271:117677.

[32]LohrenzJ, BrayBG, ClarkCR, 1964. Calculating viscosities of reservoir fluids from their compositions. Journal of Petroleum Technology, 16(10):1171-1176.

[33]MahmoodpourS, SinghM, TuranA, et al., 2022a. Simulations and global sensitivity analysis of the thermo-hydraulic-mechanical processes in a fractured geothermal reservoir. Energy, 247:123511.

[34]MahmoodpourS, SinghM, BärK, et al., 2022b. Thermo-hydro-mechanical modeling of an enhanced geothermal system in a fractured reservoir using carbon dioxide as heat transmission fluid-a sensitivity investigation. Energy, 254:124266.

[35]MoinfarA, VaraveiA, SepehrnooriK, et al., 2012. Development of a novel and computationally-efficient discrete-fracture model to study IOR processes in naturally fractured reservoirs. SPE Improved Oil Recovery Symposium, p.1-17.

[36]NorbeckJH, McClureMW, LoJW, et al., 2016. An embedded fracture modeling framework for simulation of hydraulic fracturing and shear stimulation. Computational Geosciences, 20(1):1-18.

[37]PruessK, 1991. TOUGH2: a General-Purpose Numerical Simulator for Multiphase Fluid and Heat Flow. LBL-29400, Lawrence Berkeley Lab, Berkeley, USA.

[38]QiuYL, WuCJ, ChenWF, 2020. Local heat transfer enhancement induced by a piezoelectric fan in a channel with axial flow. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(12):1008-1022.

[39]RenG, JiangJ, YounisRM, 2016. Fully coupled geomechanics and reservoir simulation for naturally and hydraulically fractured reservoirs. The 50th U.S. Rock Mechanics/Geomechanics Symposium, p.1-12.

[40]RyderRT, 1996. Fracture Patterns and Their Origin in the Upper Devonian Antrim Shale Gas Reservoir of the Michigan Basin: a Review. Open-File Report 96-23, U.S. Geological Survey, Reston, USA.

[41]ShahM, ShahS, SircarA, 2017. A comprehensive overview on recent developments in refracturing technique for shale gas reservoirs. Journal of Natural Gas Science and Engineering, 46:350-364.

[42]SongWH, YaoJ, LiY, et al., 2016. Apparent gas permeability in an organic-rich shale reservoir. Fuel, 181:973-984.

[43]StrioloA, ColeDR, 2017. Understanding shale gas: recent progress and remaining challenges. Energy & Fuels, 31(10):10300-10310.

[44]SunH, YaoJ, CaoYC, et al., 2017. Characterization of gas transport behaviors in shale gas and tight gas reservoirs by digital rock analysis. International Journal of Heat and Mass Transfer, 104:227-239.

[45]UrbanE, OrozcoD, FragosoA, et al., 2016. Refracturing vs. infill drilling–a cost effective approach to enhancing recovery in shale reservoirs. SPE/AAPG/SEG Unconventional Resources Technology Conference, p.2934-2953.

[46]VermylenJP, 2011. Geomechanical Studies of the Barnett Shale, Texas, USA. PhD Thesis, Stanford University, California, USA.

[47]VersteegHK, MalalasekeraW, 1995. An Introduction to Computational Fluid Dynamics: the Finite Volume Method. Longman Scientific & Technical, New York, USA.

[48]WangDY, YaoJ, ChenZX, et al., 2019. Image-based core-scale real gas apparent permeability from pore-scale experimental data in shale reservoirs. Fuel, 254:115596.

[49]WebbSW, PruessK, 2003. The use of Fick’s law for modeling trace gas diffusion in porous media. Transport in Porous Media, 51(3):327-341.

[50]WuYS, LiJF, DingDY, et al., 2014. A generalized framework model for the simulation of gas production in unconventional gas reservoirs. SPE Journal, 19(5):845-857.

[51]XuRN, ZengKC, ZhangCW, et al., 2017. Assessing the feasibility and CO₂ storage capacity of CO₂ enhanced shale gas recovery using triple-porosity reservoir model. Applied Thermal Engineering, 115:1306-1314.

[52]YanX, HuangZQ, YaoJ, et al., 2016. An efficient embedded discrete fracture model based on mimetic finite difference method. Journal of Petroleum Science and Engineering, 145:11-21.

[53]YanX, HuangZQ, YaoJ, et al., 2018a. An efficient hydro-mechanical model for coupled multi-porosity and discrete fracture porous media. Computational Mechanics, 62(5):943-962.

[54]YanX, HuangZQ, YaoJ, et al., 2018b. An efficient numerical hybrid model for multiphase flow in deformable fractured-shale reservoirs. SPE Journal, 23(4):‍1412-1437.

[55]YanX, HuangZQ, ZhangQ, et al., 2020. Numerical investigation of the effect of partially propped fracture closure on gas production in fractured shale reservoirs. Energies, 13(20):5339.

[56]YeX, TonmukayakulP, WeaverJD, et al., 2012. Experiment and simulation study of proppant pack compression. SPE International Symposium and Exhibition on Formation Damage Control, p.1-12.

[57]YuW, SepehrnooriK, 2014. Simulation of gas desorption and geomechanics effects for unconventional gas reservoirs. Fuel, 116:455-464.

[58]ZengQD, YaoJ, ShaoJF, 2018. Numerical study of hydraulic fracture propagation accounting for rock anisotropy. Journal of Petroleum Science and Engineering, 160:422-432.

[59]ZengQD, YaoJ, ShaoJF, 2019. Study of hydraulic fracturing in an anisotropic poroelastic medium via a hybrid EDFM-XFEM approach. Computers and Geotechnics, 105:51-68.

[60]ZhangQ, BorjaRI, 2021. Poroelastic coefficients for anisotropic single and double porosity media. Acta Geotechnica, 16(10):3013-3025.

[61]ZhangQ, YanX, ShaoJL, 2021. Fluid flow through anisotropic and deformable double porosity media with ultra-low matrix permeability: a continuum framework. Journal of Petroleum Science and Engineering, 200:108349.

[62]ZhangQ, YanX, LiZH, 2022. A mathematical framework for multiphase poromechanics in multiple porosity media. Computers and Geotechnics, 146:104728.

[63]ZhuGP, KouJS, YaoBW, et al., 2019. Thermodynamically consistent modelling of two-phase flows with moving contact line and soluble surfactants. Journal of Fluid Mechanics, 879:327-359.

[64]ZienkiewiczOC, TaylorRL, 2000. The Finite Element Method: Solid Mechanics. Butterworth-Heinemann, Oxford, UK.

[65]ZuloagaP, YuW, MiaoJJ, et al., 2017. Performance evaluation of CO₂ huff-n-puff and continuous CO₂ injection in tight oil reservoirs. Energy, 134:181-192.