Similar articles

Abstract: Most automatic steering systems for large tractors are designed with hydraulic systems that run on either constant flow or constant pressure. Such designs are limited in adaptability and applicability. Moreover, their control valves can unload in the neutral position and eventually lead to serious hydraulic leakage over long operation periods. In response to the problems noted above, a multifunctional automatic hydraulic steering circuit is presented. The system design is composed of a 5-way-3-position proportional directional valve, two pilot-controlled check valves, a pressure-compensated directional valve, a pressure-compensated flow regulator valve, a load shuttle valve, and a check valve, among other components. It is adaptable to most open-center systems with constant flow supply and closed-center systems with load feedback. The design maintains the lowest pressure under load feedback and stays at the neutral position during unloading, thus meeting the requirements for steering. The steering controller is based on proportional-integral-derivative (PID) running on a 51-microcontroller-unit master control chip. An experimental platform is developed to establish the basic characteristics of the system subject to stepwise inputs and sinusoidal tracking. Test results show that the system design demonstrates excellent control accuracy, fast response, and negligible leak during long operation periods.

Excellent and valuable work.

基于比例控制的农业机械自动转向系统研究

[1]Âström, K.J., Albertos, P., Quevedo, J., 2001. PID control. Contr. Eng. Pract., 9(11):1159-1161.

[2]Chen, W.L., Xie, B., Song, Z.H., et al., 2006. Electro-hydraulic power steering system for tractors. Trans. Chin. Soc. Agric. Eng., 22(10):122-125 (in Chinese).

[3]Dong, Z.L., Zhang, Q., Han, S.F., 2002. Control of an electrohydraulic steering system using a PID controller with a nonlinear compensation algorithm. Proc. SPIE, p.87-95.

[4]García-Pérez, L., García-Alegre, M.C., Ribeiro, A., et al., 2008. An agent of behaviour architecture for unmanned control of a farming vehicle. Comput. Electron. Agric., 60(1):39-48.

[5]He, Q., Gao, H.W., Li, H.W., et al., 2007. Electrohydraulic steering control system of tractor based on DSP. Trans. Chin. Soc. Agric. Mach., 38(5):1-5 (in Chinese).

[6]Inoue, K., Murakami, N., Miyaura, S., 2004. A modeling of a movement of a semi-crawler tractor and an adaptive operational steering control. Proc. Conf. on Automation Technology for Off-Road Equipment, p.348-359.

[7]Luo, X.W., Zhang, Z.G., Zhao, Z.X., et al., 2009. Design of DGPS navigation control system for Dongfanghong X-804 tractor. Trans. Chin. Agric. Eng., 25(11):139-145 (in Chinese).

[8]Qiu, H., Zhang, Q., Reid, J.F., 2001. Fuzzy control of electrohydraulic steering systems for agricultural vehicles. Trans. ASAE, 44(6):1397-1402.

[9]Reid, J.F., Zhang, Q., Noguchi, N., et al., 2000. Agricultural automatic guidance research in North America. Comput. Electron. Agric., 25(1-2):155-167.

[10]Shen, W.L., Xue, J.L., Zhang, Y., 2014. Development of electro-hydraulic steering system based on agricultural vehicle. J. Hunan Agric. Univ. (Nat. Sci.), 40(3):325-329 (in Chinese).

[11]Wu, X.P., Zhao, Z.X., Zhang, Z.G., et al., 2009. Development of automatic steering control system based on Dongfanghong tractor. Trans. Chin. Soc. Agric. Mach., 40(Z1):1-5 (in Chinese).

[12]Zhang, Q., Reid, J.F., Wu, D., 2000. Hardware-in-the-loop simulator of an off-road vehicle electrohydraulic steering system. Trans. ASAE, 43(6):1323-1330.

[13]Zhu, Z.X., Chen, J., Yoshida, T., et al., 2007. Path tracking control of autonomous agricultural mobile robots. J. Zhejiang Univ.-Sci. A, 8(10):1596-1603.

[14]Ziegler, J.G., Nichols, N.B., 1993. Optimum settings for automatic controllers. J. Dyn. Syst. Meas. Contr., 115(2B):220-222.