Similar articles

Abstract: In this study, we designed an oil-filled motor that can be used at full-ocean depths, and investigated the friction losses caused by the rotating seal and the properties of the oil. The direct current (DC) motor is encapsulated in an aluminum alloy housing. A rubber diaphragm is used to balance the internal and external pressures so that the motor can work on the seabed without pressure difference. To study the resistance caused by the rotating seal, a numerical model of the Glyd ring and the rotating shaft was established. Results from a rotational torque test agreed with those from numerical analysis. The kinematic viscosity of four oils was measured at 1–25 °C. Oil bath experiments in an incubator showed that the resistance from oil is highly correlated with its dynamic viscosity. Dimethicone appears to be very suitable as an insulating oil for these motors. The working characteristics of the motor were tested in a high-pressure chamber. The results showed that the motor needs to overcome higher oil resistance under higher pressure. A prototype of a pressure-adaptive motor was designed and applied successfully in the hadal zone at a water depth of more than 10000 m.

全海深充油电机设计及其摩擦损耗特性研究

[1]BaiYF, ZhangQF, FanYL, et al., 2018. Research and experiment on viscous friction power loss of deep-sea electric manipulator. Proceedings of OCEANS-MTS/IEEE Kobe Techno-Oceans, p.1-4.

[2]BaiYF, ZhangQF, ZhangAQ, 2021. Modeling and optimization of compensating oil viscous power for a deep-sea electric manipulator. IEEE Access, 9:13524-13531.

[3]CaiMJ, WuSJ, YangCJ, 2016. Effect of low temperature and high pressure on deep-sea oil-filled brushless DC motors. Marine Technology Society Journal, 50(2):83-93.

[4]ChenJW, HuangY, LinY, et al., 2020. A novel sediment pressure sampling device carried by a hadal-rated lander. Journal of Marine Science and Engineering, 8(11):839.

[5]DuMR, PengXT, ZhangHB, et al., 2021. Geology, environment, and life in the deepest part of the world’s oceans. The Innovation, 2(2):100109.

[6]DubbiosoG, MuscariR, di MascioA, 2014. Analysis of a marine propeller operating in oblique flow. Part 2: very high incidence angles. Computers & Fluids, 92:56-81.

[7]FuM, YanH, YinZY, et al., 2019. Coupling calculation of 3D whole domain steady flow and temperature field for underwater oil-filled brushless DC motors. Proceedings of the 22nd International Conference on Electrical Machines and Systems, p.1-6.

[8]GasparotoHF, ChocronO, BenbouzidM, et al., 2021. Advances in reconfigurable vectorial thrusters for adaptive underwater robots. Journal of Marine Science and Engineering, 9(2):170.

[9]JiB, LuoXW, PengXX, et al., 2012. Numerical analysis of cavitation evolution and excited pressure fluctuation around a propeller in non-uniform wake. International Journal of Multiphase Flow, 43:13-21.

[10]KangYJ, LiuSJ, ZouWS, et al., 2019. Design and analysis of an innovative deep-sea lifting motor pump. Applied Ocean Research, 82:22-31.

[11]LiGR, ChenXP, ZhouFH, et al., 2021. Self-powered soft robot in the Mariana trench. Nature, 591(7848):66-71.

[12]LiJJ, XuYX, ZouJB, et al., 2009. Rotor eddy-current loss of permanent magnet machine in brushless AC and DC modes, used for deep-sea HUV’s propeller. Proceedings of the International Conference on Electrical Machines and Systems, p.1-4.

[13]LiJJ, ZhouJB, JiangXT, et al., 2010. Electrical-thermal coupled calculation of a submersible motor used for deep-sea electromagnetic propeller. Proceedings of the Digests of the 14th Biennial IEEE Conference on Electromagnetic Field Computation, p.1.

[14]MengJH, 2021. Sliding mode variable structure chaos control for propulsion motor of deep sea robot. Journal of Physics: Conference Series, 2025:012077.

[15]QiuZL, 2008. Design and research on a variable ballast system for deep-sea manned submersibles. Journal of Marine Science and Application, 7(4):255-260.

[16]RomanovVS, GoldsteinVG, 2018. The dynamic improvement methods of energy efficiency and reliability of oil production submersible electric motors. Journal of Physics: Conference Series, 944:012099.

[17]SmithKL, TealJM, 1973. Deep-sea benthic community respiration: an in situ study at 1850 meters. Science, 179(4070):282-283.

[18]UmapathyA, BabuSM, VedachalamN, et al., 2019. Influence of deep-sea ambient conditions in the performance of pressure-compensated induction motors. Marine Technology Society Journal, 53(1):67-73.

[19]WangH, ChenJW, WangYH, et al., 2020. Research and analysis of pressure-maintaining trapping instrument for macro-organisms in hadal trenches. Journal of Marine Science and Engineering, 8(8):596.

[20]XuYM, MengDW, LiuYL, et al., 2010. Amelioration research of submersible motor design method. Proceedings of the Asia-Pacific Power and Energy Engineering Conference, p.1-4.

[21]ZhangX, LuanZD, YanJ, et al., 2012. Development of a deep-sea sediment long coring system based on a Jackhammer for R/V Kexue. Proceedings of the Oceans, p.1-6.

[22]ZouJB, QiWJ, XuYX, et al., 2012. Design of deep sea oil-filled brushless DC motors considering the high pressure effect. IEEE Transactions on Magnetics, 48(11):4220-4223.