Similar articles

Abstract: Mounds of spatter are generated in laser powder-bed fusion (L-PBF) additive manufacturing, which reduces build quality and laser lifetime. Due to the lack of supplemental airflow above the chamber, the conventional build chamber with a single gas inlet exhibits a pronounced tendency for gas to flow upward near the outlet. This phenomenon results in the formation of a large vortex within the build chamber. The vortex leads to the chaotic motion trajectory of the spatter in the build chamber. The design defects of the existing build chamber based on dual gas inlets are shown in this paper. We established a coupled computational fluid dynamics-discrete phase model (CFD-DPM) model to optimize the build chamber by adjusting the position and structure of the second gas inlet. The homogeneity of the flow is increased with a distance of 379 mm between the two inlets and a wider-reaching second inlet. The coanda effect is also crucial in the spatter-removal process. The coanda effect is reduced by modifying the right sidewall of the build chamber and increasing the pressure difference between the inlet and outlet. Finally, we found that the spatter-removal rate rose from 8.9% to 76.1% between the conventional build chamber with a single gas inlet and the optimized build chamber with two gas inlets.

采用一种双进气口进气系统提高激光粉末床熔融中的飞溅物去除率

[1]AmiriM, PaytonEJ, 2021. An analytical model for prediction of denudation zone width in laser powder bed fusion additive manufacturing. Additive Manufacturing, 48:102461.

[2]AndaniMT, DehghaniR, Karamooz-RavariMR, et al., 2018. A study on the effect of energy input on spatter particles creation during selective laser melting process. Additive Manufacturing, 20:33-43.

[3]AnnovazziA, DembinskiL, BlanchetE, et al., 2022. Influence of residual pressure on the melting of a powder bed induced by a laser beam. Journal of Manufacturing Processes, 73:715-724.

[4]Bin AnwarA, PhamQC, 2017. Selective laser melting of AlSi10Mg: effects of scan direction, part placement and inert gas flow velocity on tensile strength. Journal of Materials Processing Technology, 240:388-396.

[5]Bin AnwarA, PhamQC, 2018. Study of the spatter distribution on the powder bed during selective laser melting. Additive Manufacturing, 22:86-97.

[6]Bin AnwarA, IbrahimIH, PhamQC, 2019. Spatter transport by inert gas flow in selective laser melting: a simulation study. Powder Technology, 352:103-116.

[7]ChienCY, LeTN, LinZH, et al., 2021. Numerical and experimental investigation into gas flow field and spattering phenomena in laser powder bed fusion processing of Inconel 718. Materials & Design, 210:110107.

[8]ConstantinL, KraiemN, WuZP, et al., 2021. Manufacturing of complex diamond-based composite structures via laser powder-bed fusion. Additive Manufacturing, 40:101927.

[9]DebroyT, MukherjeeT, WeiHL, et al., 2021. Metallurgy, mechanistic models and machine learning in metal printing. Nature Reviews Materials, 6(1):48-68.

[10]DongZ, HanCJ, ZhaoYZ, et al., 2024. Role of heterogenous microstructure and deformation behavior in achieving superior strength-ductility synergy in zinc fabricated via laser powder bed fusion. International Journal of Extreme Manufacturing, 6(4):045003.

[11]FerrarB, MullenL, JonesE, et al., 2012. Gas flow effects on selective laser melting (SLM) manufacturing performance. Journal of Materials Processing Technology, 212(2):‍355-364.

[12]GaoY, ZhangCL, LiuJL, et al., 2023. Optimizing the performance of wind field circulating track in laser powder bed fusion additive manufacturing. The International Journal of Advanced Manufacturing Technology, 124(11-12):3963-3972.

[13]GresesJ, HiltonPA, BarlowCY, et al., 2004. Plume attenuation under high power Nd:yttritium‍–aluminum‍–‍garnet laser welding. Journal of Laser Applications, 16(1):9-15.

[14]GunenthiramV, PeyreP, SchneiderM, et al., 2018. Experimental analysis of spatter generation and melt-pool behavior during the powder bed laser beam melting process. Journal of Materials Processing Technology, 251:376-386.

[15]GuoQL, ZhaoC, EscanoLI, et al., 2018. Transient dynamics of powder spattering in laser powder bed fusion additive manufacturing process revealed by in-situ high-speed high-energy X-ray imaging. Acta Materialia, 151:169-180.

[16]JadhavA, JadhavVS, 2022. A review on 3D printing: an additive manufacturing technology. Materials Today: Proceedings, 62:2094-2099.

[17]KokJF, ParteliEJR, MichaelsTI, et al., 2012. The physics of wind-blown sand and dust. Reports on Progress in Physics, 75(10):106901.

[18]LadewigA, SchlickG, FisserM, et al., 2016. Influence of the shielding gas flow on the removal of process by-products in the selective laser melting process. Additive Manufacturing, 10:1-9.

[19]MatthewsMJ, GussG, KhairallahSA, et al., 2016. Denudation of metal powder layers in laser powder bed fusion processes. Acta Materialia, 114:33-42.

[20]NguyenHD, SedaoX, MauclairC, et al., 2020. Non-diffractive Bessel beams for ultrafast laser scanning platform and proof-of-concept side-wall polishing of additively manufactured parts. Micromachines, 11(11):974.

[21]PauzonC, HoppeB, PichlerT, et al., 2021. Reduction of incandescent spatter with helium addition to the process gas during laser powder bed fusion of Ti-6Al-4V. CIRP Journal of Manufacturing Science and Technology, 35:‍371-378.

[22]ShaoYP, LuH, 2000. A simple expression for wind erosion threshold friction velocity. Journal of Geophysical Research: Atmospheres, 105(D17):22437-22443.

[23]ShcheglovPY, GumenyukAV, GornushkinIB, et al., 2013. Vapor-plasma plume investigation during high-power fiber laser welding. Laser Physics, 23(1):016001.

[24]SimonelliM, TuckC, AboulkhairNT, et al., 2015. A study on the laser spatter and the oxidation reactions during selective laser melting of 316L stainless steel, Al-Si10-Mg, and Ti-6Al-4V. Metallurgical and Materials Transactions A, 46(9):3842-3851.

[25]SowMC, de TerrisT, CastelnauO, et al., 2020. Influence of beam diameter on laser powder bed fusion (L-PBF) process. Additive Manufacturing, 36:101532.

[26]TanJH, WongWLE, DalgarnoKW, 2017. An overview of powder granulometry on feedstock and part performance in the selective laser melting process. Additive Manufacturing, 18:228-255.

[27]WangD, WuSB, FuF, et al., 2017. Mechanisms and characteristics of spatter generation in SLM processing and its effect on the properties. Materials & Design, 117:‍121-130.

[28]WangJY, ZhuYW, LiH, et al., 2022. Numerical study of the flow field and spatter particles in laser-based powder bed fusion manufacturing. International Journal of Precision Engineering and Manufacturing-Green Technology, 9(4):1009-1020.

[29]YadroitsevI, GusarovA, YadroitsavaI, et al., 2010. Single track formation in selective laser melting of metal powders. Journal of Materials Processing Technology, 210(12):1624-1631.

[30]YoungZA, GuoQL, ParabND, et al., 2020. Types of spatter and their features and formation mechanisms in laser powder bed fusion additive manufacturing process. Additive Manufacturing, 36:101438.

[31]ZhangXB, ChengB, TuffileC, 2020. Simulation study of the spatter removal process and optimization design of gas flow system in laser powder bed fusion. Additive Manufacturing, 32:101049.