Similar articles

Abstract: For an electrical six-degree-of-freedom Stewart platform, it is difficult to compute the equivalent inertia of each motor in real time, as the inertia is time-varying. In this study, an analysis using kane’;s equation is undertaken of the driven torque of the movements of motor systems (including motor friction, movements of motor systems along with the actuators, rotation around axis of rotors and snails), as well as driven torque of the platform and actuators. The electromagnetic torque was calculated according to vector-controlled permanent magnet synchronous motor (PMSM) dynamics. By equalizing the driven torque and electromagnetic torque, a model was established. This method, taking into consideration the influence of counter electromotive force (EMF) and motor friction, could be applied to the real-time dynamic control of the platform, through which the calculation of the time-varying equivalent inertia is avoided. Finally, simulations with typically desired trajectory inputs are presented and the performance of the Stewart platform is determined. With this approach, the multi-body dynamics of the electrical Stewart platform is better understood.

[1]Chen, B.S., 2006. Electric Drive Control System. Mechanical Industry Press, Beijing, China, p.53-254 (in Chinese).

[2]Chen, L., Deng, Z.Q., Yan, Y.G., 2004. Design of current control loop for permanent magnet synchronous servo system. J. Nanjing Univ. Aeronaut. Astronaut., 36(2):220-225 (in Chinese).

[3]Dasgupta, B., Choudhury, P., 1999. A general strategy based on the Newton-Euler approach for the dynamic formulation of parallel manipulators. Mech. Mach. Theory, 34(6):801-824.

[4]Dasgupta, B., Mruthyunjaya, T.S., 1998. A Newton-Euler formulation for the inverse dynamics of the Stewart platform manipulator. Mech. Mach. Theory, 33(8):1135-1152.

[5]Elmas, C., Ustun, O., Sayan, H.H., 2008. A neuro-fuzzy controller for speed control of a permanent magnet synchronous motor drive. Exp. Syst. Appl., 34(1):657-664.

[6]Fichter, E.F., 1986. A Stewart platform-based manipulator general theory and practical construction. Int. J. Robot. Res., 5(2):157-182.

[7]Fu, S.W., Yao, Y., Wu, Y.Q., 2007. Comments on “A Newton-Euler formulation for the inverse dynamics of the Stewart platform manipulator” by B. Dasgupta and T.S. Mruthyunjaya. Mech. Mach. Theory, 42(12):1668-1671.

[8]Gao, X.S., Lei, D.L., Liao, Q.Z., Zhang, G.F., 2005. Generalized Stewart-Gough platforms and their direct kinematics. IEEE Trans. Robot., 21(2):141-151.

[9]Geng, Z., Haynes, L.S., Lee, J.D., Carroll, R.L., 1992. On the dynamic model and kinematic analysis of a class of Stewart platforms. Robot. Autonom. Syst., 9(4):237-254.

[10]Gough, V.E., 1956. Contribution to discussion of papers on research in automobile stability, control and tyre performance. Proc. Auto Div. Inst. Mech. Eng., p.392-394.

[11]Jan, R.M., Tseng, C.S., Liu, R.J., 2008. Robust PID control design for permanent magnet synchronous motor: a genetic approach. Electr. Power Syst. Res., 78(7):1161-1168.

[12]Ji, Z., 1993. Study of the Effect of Leg Inertia in Stewart Platforms. Int. Conf. on Robotics and Automation, 1:121-126.

[13]Kang, C.G., 2001. Closed-form force sensing of a 6-axis force transducer based on the Stewart platform. Sens. Actuat. A, 90(1-2):31-37.

[14]Khalil, W., Guegan, S., 2004. Inverse and direct dynamic modeling of Gough-Stewart robots. IEEE Trans. Robot., 20(4):754-762.

[15]Kim, N.I., Lee, C.W., 1998. High Speed Tracking Control of Stewart Platform Manipulator via Enhanced Sliding Mode Control. IEEE Int. Conf. on Robotics and Automation, p.2716-2721.

[16]Koekebakker, S.H., 2001. Model Based Control of a Flight Simulator Motion System. PhD Thesis, Delft University of Technology, the Netherlands.

[17]Liu, M.J., Li, C.X., Li, C.N., 2000. Dynamics analysis of the Gough-Stewart platform manipulator. IEEE Trans. Robot. Automat., 16(1):94-98.

[18]Omran, A., Kassem, A., El-Bayoumi, G., Bayoumi, M., 2009. Mission-based optimal control of Stewart manipulator. Aircraft Eng. Aerospace Technol., 81(3):226-233.

[19]Shim, J.H., Park, J.Y., Kwon, D.S., Kim, S., 1997. Kinematic Design of a Six Degree-of-Freedom In-Parallel Manipulator for Probing Task. Proc. IEEE Int. Conf. on Robotics and Automation, p.2967-2973.

[20]Stewart, D., 1965. A Platform with Six Degrees of Freedom. Proc. Institution of Mechanical Engineers, 180:371-386.

[21]Ting, Y., Chen, Y.S., Jar, H.C., 2004. Modeling and control for a Gough-Stewart platform CNC machine. J. Robot. Syst., 21(11):609-623.

[22]Wai, R.J., 2001. Total sliding-mode controller for PM synchronous servo motor drive using recurrent fuzzy neural network. IEEE Trans. Ind. Electron., 48(5):926-944.

[23]Yiu, Y.K., Cheng, H., Xiong, Z.H., Liu, G.F., Li, Z.X., 2001. On the Dynamics of Parallel Manipulators. Proc. IEEE Int. Conf. on Robotics and Automation, 4:3766-3771.