CLC number: TK214
On-line Access: 2024-08-27
Received: 2023-10-17
Revision Accepted: 2024-05-08
Crosschecked: 0000-00-00
Cited: 0
Clicked: 12206
WU Cun-zhen, SUN Zhi-jian, XU Jian-feng, QIN Yue-hui. Numerical prediction of temperature distribution in thermoset composites during laser curing process[J]. Journal of Zhejiang University Science A, 2002, 3(2): 162-165.
@article{title="Numerical prediction of temperature distribution in thermoset composites during laser curing process",
author="WU Cun-zhen, SUN Zhi-jian, XU Jian-feng, QIN Yue-hui",
journal="Journal of Zhejiang University Science A",
volume="3",
number="2",
pages="162-165",
year="2002",
publisher="Zhejiang University Press & Springer",
doi="10.1631/jzus.2002.0162"
}
%0 Journal Article
%T Numerical prediction of temperature distribution in thermoset composites during laser curing process
%A WU Cun-zhen
%A SUN Zhi-jian
%A XU Jian-feng
%A QIN Yue-hui
%J Journal of Zhejiang University SCIENCE A
%V 3
%N 2
%P 162-165
%@ 1869-1951
%D 2002
%I Zhejiang University Press & Springer
%DOI 10.1631/jzus.2002.0162
TY - JOUR
T1 - Numerical prediction of temperature distribution in thermoset composites during laser curing process
A1 - WU Cun-zhen
A1 - SUN Zhi-jian
A1 - XU Jian-feng
A1 - QIN Yue-hui
J0 - Journal of Zhejiang University Science A
VL - 3
IS - 2
SP - 162
EP - 165
%@ 1869-1951
Y1 - 2002
PB - Zhejiang University Press & Springer
ER -
DOI - 10.1631/jzus.2002.0162
Abstract: The temperature distribution in the advanced thermoset composite during the laser curing process was predicted with the use of the two-dimensional thermo-chemical model presented in this paper which also gives the governing equations based on the thermal history of the curing process. The finite-difference method was used to get the temperature distribution. This paper also deals with the effect of some factors (such as the winding velocity, the tape thickness and the laser heat source) on the temperature distribution.
[1] Beyeler, E.P., Guceri, S.I., 1988. Thermal analysis of laser-assisted thermoplastic-matrix composite tape consolidation,transactions of the ASME 11 composite tape consolidation.Transactions of the ASME, 110: 424-430.
[2] Chern, B.C., Moon,T.J., Howell,J.R., 1995. Thermal analysis of in-situ curing for thermoset, hoop-wound structures using infrared heating: Part I: predictions assuming independent ccattering. Transactions of the ASME, 117: 674-680.
[3] Kim, C., Teng, H., Tucker, C.L. et al., 1995. The continuous curing process for thermoset polymer composites. Part I: modeling and demonstration. Journal of Composite materials, 29(1): 1222-1234.
[4] Kim, D.H., Han, P.G., Jin G. H. et al., 1997. A model for thermosetting composite pultrusion process. Journal of Composite Materials, 31(20): 2105-2122.
[5] Kinsey, S.P., Haji-Sheikh, A., Lou, D.Y.S., 1997. A thermal model for cure of thermoset composites, Journal of Materials Processing Technology, 63:442-449.
[6] Loos,A.C., Springer,G.S., 1983. Curing of Graphite/Epoxy Composites, Ph.D. Dissertation, University of Michigan, Ann Arbor, Michigan
[7] Patankar,S.V., 1980. Numerical Heat Transfer and Fluid Flow. Hemisphere Publishing Corporation. p.1-183.
[8] Wu,C.Z., Pan, Y., Qin Y.H., 2000. Numerical investigation on the phase change of water-saturated porous media with thermosyphon. Journal of Zhejiang University SCIENCE, 1(2): 129-135.
[9] Yi, S., Hilton, H.H., 1998. Effects of thermo-mechanical properties of composites on viscosity, temperature and degree of cure in thick thermosetting composite laminates during Curing Process, Journal of Composite Material, 32(7): 600-622.
[10] Yang, H. C., Colton, J.S., 1995. Thermal analysis of thermoplastic composites during processing. Polymer Composites, 16(3): 199-203.
Open peer comments: Debate/Discuss/Question/Opinion
<1>